Wärmer System M10 x 15mm Copper Tap Tails for Monobloc, Basin and Sink Mixers,Tap Tails Connector for Mixer Taps,Flexible Tap Tails Replacement

Product Information

The Armitage Shanks Contour 21+ Single Lever Basin Mixer Tap with c opper tails is an anti-vandal unit ideal for installation within any commercial or domestic space. It comes with extended lever handle making it particularly suitable for installation in any healthcare or disabled toilet room setting. With the washer in place the nuts can now be tightened onto the threaded bar and this is where the DIY enthusiast struggles. Use a Box Spanner

Yes they will work fine providing you are careful not to unscrew the tail whilst tightening the compression.Finding a tap set genuinely capable of operating at very low pressure is your only hope without installing a pump. The image above shows the tap at the top with the connection tails at the bottom ready to receive the hot and cold feeds. The 10mm feed pipes screw into the underside of the tap and are then machined out to become 15mm copper tails ready for the connection of 15mm feeds. The minimum pressure tap I have been able to find is 0.1 bar. It has M10 connections and the flexi tails included - but they look like they will still be restricting flow somewhat as the aperture of the tails is pretty small especially at the compression nut end. So I have been considering using some copper tap tails instead. I have also been searching for a monobloc mixer tap which has larger M12 connections for the best chance of maximising flow, however, I've not been able to find any... in fact you practically never ever see thread size included in specs!! The condemnation and imposition of sanctions on Russia and Belarus in response to Russia’s military invasion of Ukraine will have enormous implications and an impact on global trade, particularly on commodities, for years to come. The effect of the war on the building material supply in the UK is still to be determined. However, the region including Russia, Ukraine and Belarus accounted for only 1.25% of building products imported into the UK last year. The ideal arrangement is to have two pushfit elbows to connect the tails to horizontal pipes (and then to isovalves etc). With this arrangement any future replacement can be accomplished in about 15mins.

Copper tails, which are narrower where they go through the tail, increasing to 15 mm at the pipework connection end. Less restrictive than flexis, but no as good as 15 mm pipes.There are no obvious restrictions being caused by the connecting pipework. I don't need to get it anything like mains pressure, but just enough improvement to avoid having to fit a pump. As it is now, I just measured a measly 1.71 l/m. If anyone's had a similar problem perhaps you could advise? Am I on the right lines... or getting a bit carried away? I don't want to fit the new tap only to find the flow is still poor. I'd also like to exhaust all other options before fitting a pump on the whole hot water system.

This WRAS approved product is manufactured from chrome-plated brass and has 15mm copper tails. Fitted with a 5 litre per minute flow regulator, this model offers excellent water-saving properties as well as a built-in self-draining spout to reduce the risk of bacterial growth from static water. The Armitage Shanks Contour 21+ Single Lever Basin Mixer Tap with copper tails is an anti-vandal unit ideal for installation within any commercial or domestic space. It comes with extended lever handle making it particularly suitable for installation in any healthcare or disabled toilet room setting. not when in a confined space or when the fittings end up situated side by side as when connecting to monobloc tails.If you're charging by the hour Seriously, installing sinks that are so thin they can't take a normal monobloc

Thanks, I appreciate the input. I didn't know that monoblocs were more restrictive than single taps. It is slid over the thread and the other end twisted tight by putting a nail or something similar into the hole and turning. Easy!Once the tap is in the hole with the flat washer or mounting plate placed over the threaded bars, the steel washer can be slid into place also. My reason is that it makes replacement very easy and it is a more reliable method of connecting the tails than compression. When tightening compression it is all too easy to loosen the tail and cause a leak. The Intatherm safe touch thermostatic basin mixer tap, designed for both domestic and commercial applications. A new stylish design featuring Inta’s proven anti scald technology a safe touch body and a self draining spout.